RadarLevelSensorINDUSTRIAL LEVEL INSTRUMENTS
Menu

RADARLEVELSENSOR · ENGINEERING & SOURCING

Guided Wave Radar vs Non-Contact Radar vs Ultrasonic

A clear measurement principle is the start. The complete installation determines the right configuration.

Use dielectric properties, vapor, foam and internals to choose.

Radar level measurement uses electromagnetic waves. Ultrasonic measurement uses sound in the gas space. Radar can be advantageous in vacuum, changing gas conditions or dusty vessels, but it still has application limits.

Process condition80GHz non-contact radarGuided wave radarUltrasonic reference
Low dielectric liquidWeak return: antenna, range and bottom echo reviewSelect probe and threshold from model data; coaxial can helpSurface and gas-path echo must be qualified
Steam / changing gas phaseReview condensation and gas propagationHigh-pressure steam may require gas-phase compensationSound speed / attenuation can vary
Foam / turbulent surfaceFoam may absorb or scatter energyProbe path can help; conductive foam and buildup remain relevantFoam can absorb the acoustic return
Agitators / vessel internalsKeep a clear beam path; map false echoesKeep probe clear of moving parts and evaluate loadsKeep acoustic cone clear
Vacuum / negative pressureRadar does not need a gas transmission mediumPossible with rated process seal and selected probeNot suitable for a true vacuum path
Coating / solids buildupLens contamination and purge/cleaning planProbe coating, bridging and mechanical forcesTransducer coating and attenuation

Estimate the beam footprint

Geometric screening only. The nominal beam edge is not an obstruction-free or zero-energy boundary.

Beam geometry inputs
Approximate beam diameter: 0.698 m

D = 2 × distance × tan(full angle / 2). At 10 m and 4°, D ≈ 0.698 m. Add installation clearance according to the selected model; this estimate does not approve a nozzle or stilling well.

Blocking distance is a model requirement, not a zero.

Reserve the upper blocking distance from the specified reference plane and check the lower dead zone or probe-end behavior. Do not equate physical probe length with the full calibrated span. Confirm maximum fill level and overfill protection separately.

Stilling wells and bypass chambers change the installation.

Use the selected manufacturer's diameter, straightness, venting, joints, equalization-port and clearance requirements. Coaxial probes already provide a guided field; additional tubing is not universally required. Deposits or emulsion can bridge a coaxial gap.

Commission the range and the echo, then verify the loop.

  1. Verify the reference plane, tank datum, probe length and safe process isolation.
  2. Set empty/full distances, engineering units, damping and device-specific mapping.
  3. Inspect the live echo curve and false-echo map at known levels; never suppress the true level echo.
  4. Verify output scaling and fault behavior with the control system using the issued instructions.

For a P&ID, use the project instrument tagging convention and identify the function (for example, LT) and actual signal. No single decorative radar icon proves a compliant drawing.

Interface measurement needs more than an oil–water label.

Provide upper-liquid dielectric constant, lower-liquid properties, upper layer thickness range and emulsion behavior. Total level and interface may be available as separate digital variables; confirm physical outputs and host mapping.

Endress+Hauser Levelflex FMP54Reference for separate probe envelopes and gas-phase compensation in high-pressure steam.

Emerson Rosemount 5300Reference for guided-wave level/interface technology and dynamic vapor compensation.

ifm LR guided wave radarReference for IO-Link applications, launching plates and coaxial probe bridging constraints.

Technology references reviewed 19 November 2026. Original model specifications are not RLS product ratings.

ENGINEERING QUESTIONS

Resolve the installation details before ordering

Does radar always work through thick foam?

No. Foam conductivity, moisture, thickness and stability affect the return. Select and test the radar and probe for the actual medium; do not promise immunity to every foam condition.

Are 3–4 degree beams free of false echoes?

No. Nominal beam width describes a radiation pattern. Internals, multiple reflections and antenna contamination can still generate misleading echoes; placement and commissioning remain necessary.

MAKE THE PROCESS THE STARTING POINT

Send the conditions. Specify the right radar.

Media, range, temperature, pressure, nozzle and output requirements help define an offer you can evaluate.

Request a configured quote